fccjxxw.com
非常超级学习网 学习超级帮手
当前位置:首页 >> >>

尼康(nikon)D80数码相机官方维修手册


INC
VBA14001-R.3694.A 作成承認印 配布許可印
サービス

計画課



VBA14001

REPAIR MANUAL

Copyrigh c 2006 by Nikon Corporation.
Recycled paper 再生紙を使用しています

All Rights Reserved. 無断転載を禁ず !!

Printed in Japan Aug 2006

INC
S
Type ective pixels CCD Image size (pixels) Lens mount Compatible lenses * Type G or D Nikkor Micro Nikkor 85 mm f/2.8D Other AF Nikkor ? AI-P Nikkor Non-CPU

cations
Single-lens re ex digital camera 10.2 million 23.6 × 15.8 mm; total pixels: 10.75 million ? 3,872 × 2,592 (Large) ? 2,896 × 1,944 (Medium) Nikon F mount with AF coupling and AF contacts

VBA14001-R.3694.A

? 1,936 × 1,296 (Small)

All functions supported All functions supported except autofocus and some exposure modes All functions supported except 3D color matrix metering II All functions supported except 3D color matrix metering II and autofocus Can be used in mode M, but exposure meter does not function; electronic range nder can be used if maximum aperture is f/5.6 or faster. ? Excluding lenses for F3AF Equivalent in 35 mm (135) format is approx. 1.5 times lens focal length. Optical xed eye-level pentaprism –2.0 to +1.0 m -1 19.5 mm (–1.0 m -1) Type-B BriteView Clear Matte Screen Mark II with superimposed focus brackets and OnDemand grid lines Approx. 95% of lens (vertical and horizontal) Approx. 0.94 × (50 mm lens at in nity; –1.0 m -1 Quick return Instant return with depth-of- eld preview When CPU lens is attached, depth-of- eld preview button stops aperture down to value selected by user (A and M modes) or by camera (other modes)

* IX-Nikkor lenses can not be used Picture angle View nder Diopter Eyepoint Focusing screen Frame coverage

Lens aperture

Self-timer Focus-area selection Lens servo

Electronically controlled timer with 2, 5, 10 or 20 s duration Focus area can be selected from 11 focus areas ? Autofocus (AF): Instant single-servo AF (AF-S); continuous-servo AF (AF-C); auto AFS/AF-C selection (AF-A); predictive focus tracking activated automatically according to subject status ? Manual focus (M) SD (Secure Digital) memory cards Compliant with Design Rule for Camera File System (DCF) 2.0 and Digital Print Order Format (DPOF) ? NEF (RAW): compressed 12-bit ? JPEG: JPEG baseline-complaint TTL phase detection by Nikon Multi-CAM 1000 autofocus sensor module –1.0 to +19 EV (ISO 100 at 20 °C/68 °F) Single-area AF, dynamic-area AF, auto-area AF Focus can be locked by pressing the shutter-release button halfway (single-servo AF) or by pressing the AE-L/AF-L button 100 to 1600 with additional settings of up to 1 EV over 1600 in steps of / EV

Storage Media File system Compression Autofocus Detection range AF-area mode Focus lock ISO sensitivity (Recommended Exposure Index)

- M ?

-

INC
VBA14001-R.3694.A

Exposure Metering Matrix

Three-mode through-the-lens (TTL) exposure metering 3D color matrix metering II (type G and D lenses); color matrix metering II (other CPU lenses); metering performed by 420-segment RGB sensor Center-weighted Weight of 75% given to 6, 8, or 10 mm circle in center of frame Spot Meters 3.5 mm circle (about 2.5% of frame) centered on active focus area Range (ISO 100 equivalent, 0 to 20 EV (3D color matrix or center-weighted metering) f/1.4 lens, 20 °C/68 °F) 2 to 20 EV (spot metering) Exposure meter coupling CPU coupling Mode Digital Vari-Program ( auto, portrait, landscape, macro close-up, sports, night landscape, nigh portrait); programmed auto (P) with exible program; shutterpriority auto (S); aperture-priority auto (A); manual (M) Exposure compensation –5 to +5 EV in increments of / or ? EV Bracketing Exposure and / or ash bracketing (2–3 exposures in increments of ? or ? EV) Exposure lock Exposure locked at detected value with AE-L/AF-L button Electronically-controlled vertical-travel focal plane shutter 30 to ? s in steps of ? or ? EV, bulb Auto (TTL white balance with 420-segment RGB sensor); six manual modes with ne tuning; color temperature setting; preset white balance 2 to 3 exposures in increments of 1, 2, or 3 ? , , , : Auto ash with auto pop-up ? P, S, A, M: Manual pop-up with button release Approx. 13/42 at ISO 100 and 20 °C (68 °F) X-contact only; ash synchronization at shutter speeds of up to ? s TTL ash control by 420-segment RGB sensor ? SB-800, SB-600: i-TTL balanced ll- ash for digital SLR and standard i-TTL ll- ash for digital SLR Available with SB-800 and CPU lens Available with such Speedlights as SB-800, 80DX, 28DX, 28, 27, and 22s Available with SB-800 ? , , : Auto, auto with red-eye reduction; ll- ash and red-eye reduction available with optional Speedlight ? : Auto, auto slow sync, auto slow sync with red-eye reduction; slow sync and slow sync with red-eye reduction available with optional Speedlight ? , , : Fill- ash and red-eye reduction available with optional Speedlight ? P, S, A, M: Fill ash, slow sync, rear-curtain sync, red-eye reduction, slow sync with redeye reduction Lights when built-in ash or SB-series Speedlight such as 800, 600, 80DX, 28DX, 50DX, 28, 27, or 22s is fully charged; blinks for about 3 s after ash is red at full output Standard ISO hot-shoe contact with safety lock With SB-800, 600, and R200, supports Advanced Wireless Lighting (SB-600 and R200 only support AWL when used as remote ash), Auto FP High-Speed Sync, Flash Color Information Communication, modeling Flash, and FV Lock. 2.5 in., 230,000-dot, low-temperature polysilicon TFT LCD with brightness adjustment Can be selected from NTSC and PAL USB 2.0 Hi-speed ? in. (ISO)

Shutter Speed White balance Bracketing

Guide number (m/ft) Flash Sync contact Flash control TTL Auto aperture Non-TTL auto Range-priority manual Flash mode

Flash-ready indicator Accessory shoe Nikon Creative Lighting System Monitor Video output External interface Tripod socket

- M ?

-

INC
VBA14001-R.3694.A

Firmware upgrades Supported languages Power source

Firmware can be upgraded by user Chinese (Simpli ed and Traditional), Dutch, English, Finnish, French, German, Italian, Japanese, Korean, Polish, Portuguese, Russian, Spanish, Swedish ? One rechargeable Nikon EN-EL3e Li-ion battery; charging voltage (MH-18a quick charger): 7.4 V DC ? MB-D80 Multi-Power battery pack (available separately) with one or two rechargeable Nikon EN-EL3e Li-ion batteries or six LR6 alkaline, HR6 Ni-MH, FR6 lithium, or ZR6 nickel manganese AA batteries ? EH-5 AC adapter (available separately) Approx. 132 × 103 × 77 mm (5.2 × 4.1 × 3.0 in.) Approx. 585 g (1 lb. 5 oz.) without battery, memory card, body cap, or LCD monitor cover 0 to +40 °C (+32 to 104 °F) Less than 85% (no condensation)

Dimensions (W × D × H) Weight Operating environment Temperature Humidity

Unless otherwise stated, all gures are for a camera with a fully-charged battery operating at an ambient temperature of 20 °C (68 °F).

Speci cations Nikon reserves the right to change the speci cations of the hardware and software described in this manual at any time and without prior notice. Nikon will not be held liable for damages that may result from any mistakes that this manual may contain.

- M ?

-

INC
VBA14001-R.3694.A

Points to notice for Disassembly / Assembly

WARNING 警告
Due to an internal high voltage area, take extra care not to get 内部に高電圧部あり。カバーを外す時は感電に注意すること。 an electric shock when detaching covers. カバーを外した後は、修理指針の指示に従ってメインコンデン After removing covers, be sure to discharge the main condenser according to the instructions of repair manuals. サーの放電を必ず行うこと。

Note: ① When disassembling/(re)assembling, be sure to use the conductive mat (J5033) and wrist strap (J5033-5) for static protection of electrical parts. ② Before disassembling, be sure to remove batteries or AC power wires. ③ When disassembling, make sure to memorize the processing state of wires and FPC, screws to be fixed and their types, etc.      ④ Because the low pass filter of the imaging CCD PCB is easily damaged, handle it with enough care.

 Points to notice for Lead-free solder products
 ? Lead-free solder is used for this product.  ? For soldering work, the special solder and soldering iron are required.  ? Do NOT mix up lead-free solder with traditional solder.  ? Use the special soldering iron respectively for lead-free solder and lead solder. They cannot be used in common.

Caution: Whenever "Separation of Front and rear bodies", "Disassembly of CCD/FPC unit", or "Disassembly of Bayonet" are performed, be sure to perform "RESET AF-DEFOCUS COMPENSATION" of camera adjustment software after reassembling.

- D ?

-

INC
VBA14001-R.3694.A

Disassembly
1. Separation of Front and Rear Bodies
Bottom Cover ? Take out two screws (#692), one screw (#658) and four screws (#657). ? Remove the bottom cover.
#692×2 #658

#657×4

Bottom cover

Rear cover ? Take out two screws (#657) and two screws (#656). ? Remove the rear cover. Note: Remove the rear cover slowly so as not to cut TFT-PCB connection-FPC of the upper portion of the cover.

#657×2

#656×2

Rear cover

- D ?

-

INC
VBA14001-R.3694.A ? Remove TFT-PCB connection-FPC from the connector.

TFT-PCB connection-FPC

SB pop-up ?Cut the tracing film sheet, etc into the below size of piece. Then insert it into the clearance of the top cover pop-up part as shown right, and pop it up by sliding the sheet in the direction of the arrow.

Approx.2cm

Approx. 4cm

- D ?

-

INC
VBA14001-R.3694.A
背面カバー分解

#402 #403 #412 #413

#424 #425 #426 #427 #428

#421 #422

#401 #416 #430 #405×2 #492 #404×2 #429 #718 #408 #420 #417 #431 #432 #B431 #418 #419 #423

#670×3

#1037

#407

#668 #433 #772×2 #681×2 #B1036 #406 #670×3

#666×3

- D ?

-

INC
VBA14001-R.3694.A

WARNING 警告
内部に高電圧部あり。カバーを外す時は感電に注意すること。

Due to an internal high voltage area, take extra care not to get an electric shock when detaching covers.

カバーを外した後は、修理指針の指示に従ってメインコンデン After removing the covers, be sure to discharge the main サーの放電を必ず行うこと。 condenser according to the instructions of repar manuals.

Covers ? In order to remove the front cover (#B24) first, remove [#124], the screw (#659), [#121], and four screws (#691).
AU TO

#691×2

#71

#70 #755 #28 #638 #691×2 #124 #659 #121

#B24

#B26

#618

Discharge of Main condenser ?Discharge the main condenser from its both ends.

2KΩ/5W

Main condenser

- D ?

-

INC
VBA14001-R.3694.A
DG shield plate

? Take out six screws (#683). ? Remove DG shield plate (#B78).
#683×6

#B78

DG-PCB unit ? Remove the three FPCs, two harnesses, and four solderings. ? Take out the screw (#683) and remove the DG-PCB unit (#B1031).

#683

#B1031

Harness Harness CCD/PCB (core wire: coated) CCD/PCB (ground)

CCD/PCB (core wire: coated) CCD/PCB (ground)

- D ?

-

INC
VBA14001-R.3694.A CCD/PCB unit

? Take out three screws (#680) and remove the CCD/PCB unit (#B1032).

Caution:
#680×3 #B1032

Some bodies have already washer(s) attached on the mounting surface of CCD/PCB unit.

Preview SW/FminGND wire
#826

? Remove two stickers (#826 and #762). ? Remove four wires. ? Take out the screw (#627). The preview SW unit and the preview SW come off.
Preview switch unit #627

#762

Preview SW

Yellow Green Blue

Black

- D ?

-

INC
VBA14001-R.3694.A Top cover ? Unsolder six wires that are connected from the top cover.
Black Green Orange Gray

Blue

Red

? Take out screws (#656,#629,and #624) and two screws (#686). ? Remove the adjustable diopter unit (#280, 288, 282, 287, 281).
#280 #288 Adjustable diopter unit #282 #281

#287 #686×2

#629

#656

? Remove the top cover FPC (#1007) from the connector.

#624

#1007

- D ?

-

INC
VBA14001-R.3694.A Disassembly of Top cover SB upper case  ? Press the pop-up lever A part of the top cover unit so that the built-in SB pops up.  ? Take out two screws (#629).

Pop-up lever A part

 ? Take out two screws (#629).

#629×2

 ? Release the two claws. House the built-in SB and remove the SB upper case (#301).

SB upper case (#301) Claw

- D ?

-

INC
VBA14001-R.3694.A Top cover FPC / Wiring ? Remove the M/D FPC. ? Unsolder two SB pop-up SW wires. ? Remove five solders of the accessory shoe contacts.

M/D FPC

Yellow: SB pop-up SW wire

Green: SB pop-up SW wire Accessory shoe contacts×5

? Remove the screw (#607). ? Remove the remote control unit (#B1056). ? Remove the bundled wires.
#607

#B1056

Bundled wires

- D 0 ?

-

INC
VBA14001-R.3694.A Flash-up spring ?Unhook the Flash-up spring (#305). ?Take out the screw (#650) and remove the flash-up spring (#305).
#305

#650

SB lower case unit ?Pull each wire out of holes. ?Loosen two hooks of the collar (#308), and remove [#308]. ?Remove the SB-case rotate shaft (#306). ?Detach the SB lower case unit (#B2302) from the top cover. ? Remove [#B341] and [#B342].
#B2302 Caution:Be careful NOT to deform the SB POP-UP switch.

#B341 #B342

AU TO

2 hooks

#306

#308

- D  ?

-

INC
VBA14001-R.3694.A M/DFPC unit ? Take out three screws (#640), and remove the M/DFPC unit (#B2455). ? Remove the delete-button rubber SW (#399) and the delete button (#398).

AU TO

#398 #399
#B2455

#B2455

#640×3 #640

AF-assist illuminator window / Command dial ? Unsolder the command dial (#B367 and #B377). ? Take out the two screws (#610) of [#B367]. ? Take out the two screws (#607) of [#B377]. ? Remove the command dials (#B367 and #B377).
#607×2

#B377 Solder

#B367
#B367

#B377

Solder

#610×2

- D  ?

-

INC
VBA14001-R.3694.A Top cover FPC unit ? Take out four screws (#610). ? Take out the screw (#612). ? Take out the screw (#611). ? Remove the top cover FPC unit (#B11007). ? Remove the AE-L rubber SW (#399) and AE-L button (#381). ? Remove the light-leak prevention sponge (#825).
#610×4

#825

#B11007 #612

#381 #399

AU TO

#611

#825

#B11007

#331

#332×2 #1044 #333 #334 #1077

#806 #1017 #1135 #1136 #611 #738 #612 #610×4 #805 #771 #840

#330 #B1011

- D  ?

-

INC
VBA14001-R.3694.A Release button / other small parts

#335

#460

AU TO

#454

#461 #338

#383 #384

#350

#351 #345 #722 #346

#387×2 #347 #349 #340

#398

#399

#348

#339 #380

#690×2

- D  ?

-

INC
VBA14001-R.3694.A Outer LCD window / shoe mold unit / accessory shoe / other small parts

#318

#316

#B317

#451

#142

#453 #452 #605×3 #640 #326

#463

#758×2 #756×2

#321

#322

#654×4 #337×2 #336×2

- D  ?

-

INC
VBA14001-R.3694.A

Sub-PCB unit
? Unsolder three wires. ? Disconnect three FPCs from each connector. ? Take out the screw (#623) and two screws (#640).
#623 Gray Black FG/ID connect spring AF-assist illuminator Black #640 AF-assist illuminator

Main PCB unit (#B1001) #640 Sub-PCB unit (#1002)

?Disconnect the sub-PCB unit (#1002) from the underneath connector of the main PCB. ? AF-assist illuminator unit (#B325) comes off. ? Remove two FPCs. ? Remove four wires.
Sub-PCB unit (#1002)

AF-assist illuminator unit (#B325)

Main PCB connector

Black Front body FPC unit Red Front body FPC unit Blue SQ unit Orange SQ unit

- D  ?

-

INC
VBA14001-R.3694.A Separation of Front and Rear bodies ? Take out two screws (#615), and remove the eyepiece mold (#291). ? Take out two screws (#699), four screws (#634), two screws (#615) and one screw (#621). Then remove the front body.
#291 #615×2

#634×4

#699×2

#621

#615×2

- D  ?

-

INC
VBA14001-R.3694.A

3. Rear body
Main PCB unit

? Remove connection-FPC (#1023). ? Unsolder two wires of electronic buzzer unit. ? Disconnect the FPC of the main PCB from the DC/DC connector. ? Take out two screws (#695). ? Remove the main PCB unit(#B1001).
Main PCB unit (#B1001)

Black Electronic buzzer Black Electronic buzzer

Connection-FPC (#1023)

Connection-FPC (#1023) #695×2

DC/DC connector

GND-plate C unit ? Take out two screws (#607) and one screw (#610). Then remove [#B109].
#607×2

FPC of Main PCB

#B109

#610

- D  ?

-

INC
VBA14001-R.3694.A DC/DC PCB unit ? Remove [#110]. ? Unsolder six wires. ? Disconnect the rechargeable-battery wire (#1059) from the connector. ? Remove two harnesses. ? Take out the screw (#610). ? Remove DC/DC PCB unit (#1030).
Rechargeable-battery wire (#1059) #610

Harness

DC/DC PCB unit (#1030)

Red: battery-contact spring Black: battery-contact spring

#110 Yellow: SB-PCB Red: Blue: SB-PCB SB-PCB Black: SB-PCB

SB PCB ? Remove the FPC. ? Remove six wires.
Blue

Pink

Red Black Yellow Blue FPC

- D  ?

-

INC
VBA14001-R.3694.A Bottom wires

Black

? Detach the four wires from the bosses.

Red Blue Yellow

SB/IF PCB unit (#B1041)

SB PCB ? Remove the main condenser (#1043) from the adhesive double-coated tape. ? Take out two screws (#608). ? Remove SB/IF-PCB unit (#B1041). ? Remove SB/IF-PCB GND plate (#75).
SB/IF PCB unit (#B1041) #608×2 #75 SB/IF PCB GND plate #763

Adhesive doublecoated tape (#753) #608×2

#754

Main condenser (#1043)

- D 0 ?

-

INC
VBA14001-R.3694.A GND plate ? Take out the screw (#607), and remove [#108]. ? Remove [#102]. ? Take out two screws (#633), and remove [#107].
#607 #102

#107 #108 #633×2

? Take out the screw (#603) and remove [#106].
#603

#106

- D  ?

-

INC
VBA14001-R.3694.A OP FPC unit, Electronic buzzer unit, Clock battery unit, other small parts

#619 #693 #157 #80 #619 #517 #B1016 #694×3

#607 #1055 #1059 #617×2

#162 #754

#146

#617×2

#150 #760

#145

#149

#828

#764×2

#788

#761×2

- D  ?

-

INC
VBA14001-R.3694.A

3. Front Body
P-BOX section ? Remove two fingers (#136). ? Remove the gasket (#481). ? Remove the tracing film sheet (#783). ? Take out four screws (#642) and remove the P-BOX section.

#642×4

P-BOX section

#481

#136×

2

#783

- D  ?

-

INC
VBA14001-R.3694.A In-finder LCD FPC unit ? Disconnect the in-finder LCD FPC from the connector. ? Take out two screws (#626), and remove the in-finder LCD FPC unit (#B1010).

In-finder LCD FPC unit #B1010 #626×2 #508
In-finder LCD FPC unit

#1045 #509

P-BOX unit  Metering FPC unit 

Eyepiece lens unit
? Take out three screws (#644), and remove the metering FPC unit (#B11008).

? Take out two screws (#642), and remove the eyepiece lens unit. #644×3 #B11008

Eyepiece lens unit

#522 #523 #11

#642×2

#774 #7 #603 #278 #286 #283 #284 #603

#277 #B276 #274 #271 #279 #275 #5 #782 #290 #272 Eyepiece lens unit

- D  ?

-

INC
VBA14001-R.3694.A Penta unit ? Disconnect SI-FPC (#1022) from the connector of [#1021]. ? Remove the soldering bridge that joints [#1021] and [#1027].
#839 Connector

#1021

Soldering bridge

#1027

#776 #270

#775 #267

#269

#268×2 #4

#298 #535,535B,C #503×2 #504×2 #502×2 #8 #532 SI-FPC #1022 #610×2 #264

#610×2

#532

#521

- D  ?

-

INC
VBA14001-R.3694.A

#777

#RP-B261

#526×2 #507 #1022 #534 #263 #1046 #501 #510 #527 #266A,B×0 ~ 1 #3 #265 #529 #530

#511

- D  ?

-

INC
VBA14001-R.3694.A  AFCCD FPC unit

? Remove the tape (#734). ? Remove AFCCD-FPC. ? Take out three screws (#173) with Hexagonal wrench (φ1.5mm) to remove AFCCD FPC unit (#B2163). ? Three springs (#170) come off, too.

AF CCD-FPC

#734

AF CCD FPC unit (#B2163)

#173×3

#170×3

- D  ?

-

INC
VBA14001-R.3694.A Shutter unit

? Remove the tape [TA-0009(22×30)]. ? Unsolder the five wires.
Green Orange White Gray Violet

TA-0009(22×30)

? Remove the sponge (#824). ? Deactivate the preview latch lever. Then, rotate "A" in the direction of the arrow and raise the mirror. ? Take out two screws (#638), and remove the shutter unit (#B31).
#824

#638×2

#B31

Deactivation Preview latch lever

Rotation direction A

- D  ?

-

INC
VBA14001-R.3694.A Front body FPC unit ? Unsolder four wires. ? Remove the two soldering bridges .
Yellow:
AM-change SW wire

Black:
AM-change SW wire

Soldering bridge

Yellow:
AF motor wire

Black:
AF motor wire

Soldering bridge

? Remove the sponge (#822). ? Remove the soldering bridges, and remove the front body FPC.
#709 Red: Main PCB Black: Main PCB

#822

Soldering bridges Front body FPC

- D  ?

-

INC
VBA14001-R.3694.A Aperture control unit Procedure 1. Remove two wires. 2. Take out two screws (#624) and one screw (#698). 3. Press down the aperture lever with finger, and move the aperture coupling lever (#207) the direction of arrow ( ① ). 4. In state of 3., while letting the arm of [#RP-B241] escape, remove the aperture control unit (#RP-B241) by pulling it in the direction indicated by arrow ( ② ).
Brown: Fmin SW Black: Fmin SW

#624

Arm of [#RP-B241]

#207 Arrow ① Arrow ②

#624 Aperture lever

#RP-B241

#698

- D 0 ?

-

INC
VBA14001-R.3694.A Aperture control PCB SQ unit

#1109 #1110

#TA-0009

#B91

#214

#RP-B241

#630 #628

- D  ?

-

INC
VBA14001-R.3694.A AF driving unit Lens release button / Vertical lever / Horizontal lever areas

? Remove the horizontal lever (#193), and remove the AF motor PCB (#B172). ? Remove the vertical lever (#191), and remove the release-button holder (#B116).

#642 #115 #625 #119 #B116 #637×2 #191 #630

#B172 #122

#123 #607

#185 #195 #652 #630 #193

- D  ?

-

INC
VBA14001-R.3694.A Bayonet / A/M-change SW / Lens-contact areas

#1115 #642 #1116 #B2113

#642×2

#126

#B125 #235 #120 #689×2 #238 #237 #114 #112×3 #111 #818 #132 #131

#660 #648×5

#1134 #135

- D  ?

-

INC
VBA14001-R.3694.A Aperture lever / F-min SW / Preview locking-lever areas

#206 #203 #209 #207 #210 #208 #639 #205

#204

#212 #1122 #642 #213 #134 #B133 #624 #202 #221 #1121 #223 #224 #222

Mirror unit ?Note that two pins (#240) and the pin (#236) are attached with the Super X.

#B2231

#199

#197

#198

#240×2 #236

- D  ?

-

INC
Assembly/ Adjustment
1. Front body
Mirror unit #199 #B2231

VBA14001-R.3694.A NOTE: For undescribed tapes and sponges here ? in"Assembly", refer to PARTS LIST.

#197

#198

#240 × 2 #236

? With being mirror-up as shown right, assemble the pins and apply the adhesive (Super X) on each pin.

#236

Adhesive Super X

Adhesive Super X

Apply the adhesive only on 1/4 periphery of the pin on mount side.

Do NOT allow the adhesive to be forced out on the head of #240.

- A ?

-

INC
Aperture lever F-min SW areas  Apply Grease: LEN317A to the VBA14001-R.3694.A

inner diameter surface of #203, #207, and #208.

#204 #206 #203 #209 #207 #210 #208 #639 #213 #205 #212 #1122 #1121 #642 #134 #B133

Apply Grease: MZ-800S

to

the overall of #209 and #210.

Brown

Black

Position for hooking spring

#205

#212

(Short) #205

Long (thin) #212 Long (thick) #213

Grease: LEN317A

Grease: LEN317A

- A ?

-

INC
VBA14001-R.3694.A Preview latch lever

Grease: LEN317A

#223 #202 #624 #221

#222 #224 Hold the one part of the spring, then wind and hook it to the protrusion of [#221].

Aperture control unit SQ unit
#1109 #1110

#TA-0009

#B91

#214

#RP-B241 #630 #628

- A ?

-

INC
Aperture control unit VBA14001-R.3694.A 1. Turn the below [1] all the way to the end. Then press [2] in the direction to lock. (ref. Fig. ① ) 2. Insert the arm between [#207] and [#203]. (ref. Fig. ② ) 3. Tighten two screws (#624) and one screw (#698). (ref. Fig. ③ and ④) Note: Be careful not to bend contact blade of F-min SW.

Fig. ①
Aperture control unit

Fig. ②

2 1

#207 #203

Arm

Fig. ③ Direction for positioning

#624×2

Fig. ④

Direction for positioning

#698

- A ?

-

INC
 AF driving unit 

VBA14001-R.3694.A

?Mount the AF motor PCB (#B172) by following the direction for positioning, and fix it with two screws (#637).

#637×2

Direction for positioning #B172

A/M change SW Lens release button

#642 #126 #B125 #B116

- A ?

-

INC
Vertical lever ? Assemble by the following order. #122→#191→#630
#191 [#191] comes under when assembled.

VBA14001-R.3694.A

#630
Grease: LEN317A

Note: Be careful NOT to bend contact blade of the lens release SW.

#122

Horizontal lever

#185 #193

? Put the coupling shaft (#185). ? Put the horizontal-lever spring (#195), and hook it to the hooking part. ? Set the horizontal lever (#193) to be engaged in the groove of [#185]. ? Fix the horizontal lever (#193) with the screw (#630).
[#185] must be engaged. #185
Hooking part

Horizontal-lever spring (#195)

#193 #630 #195 #193

Grease: LEN317A

? Unhook [#195] and hook it to [#193] again.

- A ?

-

INC
VBA14001-R.3694.A  Bayonet  AF lens contacts areas ? Fix [#123] with the screw (#607). ? Fix the lens contacts unit (#B2113) with two screws (#642). ? Put the Fmin spring (#132) and Fmin coupling block (#131) so that they can be fit in the groove. ? Attach [#135], and arrange the wire (#1134) inside the groove. ? Attach [#114]. ? Attach three plate springs [#112]. ? Fix the bayonet (#111) with the screw (#660) and five screws (#648), in the order from ① to ⑥ . ? Hook the spring (#132).
#B2113 #642×2

#235 #120 #689×2 #238 #237 #114 #123 #607 #818 #132 #131 #660 ① ②
Grease: LEN317A

#112×3

#112×3 ③ #111 ⑥



④ #648×5 #135 #1134 #131

#132

#132

- A ?

-

INC
VBA14001-R.3694.A  A/M change SW cover area

? Solder two wires. [Make soldering bridge to joint the black wire, AM change SW unit (#B125) and the mount GND spring (#114).] ? Insert [#119]. ? Mount [#115], and tighten the screws (#642 and #625).
#642

#625

#115 #119

Yellow:Front body FPC Black:Front body FPC

#114

#B125

- A ?

-

INC
VBA14001-R.3694.A  Height adjustment of AF coupling shaft ① Set the A/M change cam (#122) to AF side. [i.e. The coupling shaft (#185) sticks out of the bayonet.] ② Adjust the height of the coupling shaft (#185) with the screw (#652) so that it becomes 1.7±0.15mm. ③ After the adjustment, fix the screw (#652) with screwlock.

#652 Adhesive: Screw lock

 #185

1.7±0.15mm #122 A/M change cam

Bayonet

Height adjustment of Aperture lever

?Measure the height of the aperture lever by using the tool (J18004).      Standard: 3.4±0.1mm In case the value is out of standard, make an adjustment by bending the circled part. Caution: Be careful NOT to bend the inner part of the lever when adjusting. 

  3.4±0.1mm

Aperture lever

- A ?

-

INC
VBA14001-R.3694.A  Front body FPC

? Mount the front-body FPC unit (#1009) by fitting in eight bosses. ? Bend the FPC of the lens contacts unit (#B2113) toward bayonet side, and attach it by fitting in two bosses.

Front body FPC unit (#1009)

#709

Red wire: Main PCB

Black wire: Main PCB

FPC of lens contacts unit (#B2113)

? Make soldering bridge to joint [#1009] and the FPC of the lens contacts unit (#B2113). ? Attach the sponge (#822).
#822 Soldering bridge

- A 0 ?

-

INC
VBA14001-R.3694.A ? Set [#1014]. ? Pass [#1014] and [#1012] through the holes, and make soldering bridges. ? Solder four wires.
Yellow wire:
#1014 AM change SW wire

Black wire:

AM change SW wire

Soldering bridge

Yellow wire:

AF motor wire

Black wire:

AF motor wire

Soldering bridge

#1012

- A  ?

-

INC
VBA14001-R.3694.A Shutter unit

? Deactivate the preview latch lever. Rotate "A" in the direction of the arrow, and raise the mirror. ? Mount the shutter unit (#B31). Tighten two screws (#638) in the order from ① to ② . ? Attach the sponge (#824). ? Rotate "A" in the direction of the arrow, and let the mirror down. ? Rotate "A" as shown so that the index falls within the range of the initial position.
Range of initial position

#824 #638×2 ②



#B31

Index

Deactivation Preview latch lever

Rotation direction

Rotation direction

A

A

? Solder seven wires. ? Attach the tape [TA-0009 (22×30)].
Gray wire: Shutter White wire: Shutter Violet wire: Shutter

Green wire: Shutter Orange wire: Shutter Brown wire: Fmin SW Black wire: Fmin SW TA-0009(22×30)

- A  ?

-

INC
VBA14001-R.3694.A AF CCD FPC unit ? Put three springs (#170). ? Mount the AF CCD FPC unit (#B2163), and turn the three screws (#173) softly all the way to the end with the hexagonal wrench (φ1.5mm), then give it approx. four turns counterclockwise.
#173×3 AF CCD FPC unit #B2163

#170×3

? Connect the AF CCD FPC to the connector. ? Attach the tape (#734).

AF CCD FPC

#734

- A  ?

-

INC
VBA14001-R.3694.A  Penta unit
? Attach [#8]. ? Attach the two [#503] with the two [#502], and assemble the two [#502]. ?Mount [#1021] and [#1027], which were jointed by soldering bridges, on [#RP-B261]. Then fix them with the two [#532] and tighten two screws (#610). ? Mount the finder field frame (#264). ? Mount the prism (#4). ?Attach [#298] and [#535]. ? Mount [#269], [#267], and [#270] in order. ? Attach [#1021]. Soldering bridge #1027 #1021 #839 Connector

? Fix with the two penta prism-retaining springs (#268).

#776 #270 #775 #267

#269

#268×2 #4

#298 #535,535B,C #503×2 #610×2 #8 #532 SI-FPC #1022 #521 #RP-B261 #264

#504×2 #502×2

#610×2

#532

- A  ?

-

INC
VBA14001-R.3694.A ? Attach [#511]. ? Assemble ※ and [#265]. ? Assemble [#266] and [#3], and hold them with [#265]. ? Connect the SI-FPC (#1022) to the connector of the penta FPC unit (#1021).

#777

#RP-B261

#526×2 #507 #534 #263
Direction for positioning

#1022 #529 #530



#1046

#501

#510 #527 #266A,B×0 ~ 1 #3 #265 #511

- A  ?

-

INC
VBA14001-R.3694.A Metering FPC unit  Eyepiece lens unit ? Fix the eyepiece lens unit with two screws (#642). ? Fix the metering FPC unit (#B11008) with three screws (#644).
#B11008
[#272] must NOT stick out of [#271]. Align the grooves of [#278] and [#283], and assemble them.

#644×3

Eyepiece lens unit

#522 #523 #11

#642×2

#774 #603 #286 #283

#277 #7 #278

#B276 #274 #271 #279 #275 #5

#284 #603 #290 #782 #272

Eyepiece lens unit

In-finder LCD FPC unit ? Fix the in-finder LCD FPC unit (#B1010) with two screws (#626). ? Connect the in-finder LCD FPC to the connector.

#626×2

In-finder LCD FPC unit #B1010 #508 #1045 #509

In-finder LCD FPC unit

#B261RP

- A  ?

-

INC
VBA14001-R.3694.A P-BOX section ? Fix the P-BOX section with four screws (#642). ? Press-contact "A" part into the two bosses. ? Attach the tracing film sheet (#783). ? Put the gasket (#481). ? Attach two fingers (#136).
#642×4
Prism box section



#481

#136×

2

#783

- A  ?

-

INC
VBA14001-R.3694.A Angle inspection and adjustment of Main mirror and sub-mirror Device: 1.Main mirror 45° inspection and adjustment
① Collimator (J19110) ② Reflection mirror (J18389) ③ Optical parallel (J18037-2) ④ Hexagonal wrench
Collimator (J18037-2) J0 Bayonet

2.Sub-mirror 59° inspection and adjustment
① Collimator (J19110) ② 59° mirror tool (J18409) ③ Hexagonal wrench
Collimator

(J18409) J Bayonet

Eccentric pin for the main mirror (J18389) J Main mirror Eccentric pin for the sub-mirror Sub-mirror

Width of line indicates deviation

Standard:
Main mirror Left-right deviation Up-down deviation Distortion
± 25’     ± 10’    8’or less

Sub-mirror
    __      +5 ± 5’    8’or less Reference line
Up-down

Caution: Left-right ?Before and after the adjustment, check the accuracy by moving the main mirror up- and downwards a few times. ? Check for the up-down deviation. In case the result is out of standard, make an adjustment by turning the eccentric pin with Hexagonal wrench. ? In case the the result of checking up-downward and right-leftward deviation is out of standard, the front plate area or mirror unit should be defective. ?In case inspection and adjustment are made only with the front body, check again after assembling the front body into the rear body. - A  ? -

INC
VBA14001-R.3694.A

2. Rear body
OP FPC unit, Electronic buzzer unit, Clock battery unit, other small parts ? Lastly, fix [#B1016] with three screws (#694).
#693 Pass the wires through the hole, and arrange them between bosses.

#619 #619
Groove

Arrange the wire

#619 #157

in the space of the

#693 #80

groove.

#619 #517

#694×3

#B1016 #607 #1059 #162 #617×2 #754 #1055 #617×2 #146 #150 #760 #145 #149 #828

#764×2 #788

#162

#761×2

#1059

- A  ?

-

INC
VBA14001-R.3694.A SB PCB ?Attach the tape (#763), and put the SB/IF PCB GND plate (#75). ? Mount the SB/IF PCB unit (#B1041). ? Tighten two screws (#608). ? Position the main condenser (#1043) in the direction of the arrow, and fix it with the adhesive double-coated tape (#753 and #754).
#763 #608×2 #75 SB/IF PCB GND plate SB/IF PCB unit (#B1041) SB/IF PCB unit   (#B1041)

#753

#608×2

Direction for positioning

#754

Main condenser (#1043)

- A 0 ?

-

INC
VBA14001-R.3694.A Bottom conductive plate ?Put the bottom conductive plate (#106), and tighten the screw (#603).
#603

Bottom conductive plate (#106)

GND plate ? Put [#102] and [#108], and tighten the screw (#607). ? Put [#107], and tighten two screws (#633).

#607 #102

#107 #108 #633×2

- A  ?

-

INC
VBA14001-R.3694.A DC/DC PCB unit ? Mount the DC/DC PCB unit (#B1030). ? Connect the two harnesses to each connector. ? Tighten the screw (#610). ? Connect the rechargeable battery wire (#1059). ? Solder six wires. ? Attach [#110].
Rechargeable battery wire (#1059) #610

Harness

DC/DC PCB unit (#B1030) Red wire: Battery contacts spring ( + ) Black wire: Battery contacts spring ( - ) #110 Yellow wire: SB PCB  Blue wire: SB PCB Red wire: SB PCB Black wire: SB PCB

GND-plate C unit ? Fix [#B109] with two screws (#607) and one screw (#610).
#607×2

#B109

#610

- A  ?

-

INC
VBA14001-R.3694.A Bottom wires

? Arrange four wires among bosses.
Black wire Red wire ② Put each wire between bosses. Wires must NOT be hooked here. Blue wire Yellow wire

① Put two wires each on either side of the rib/protrusion.

③ Put each wire between bosses.

SB PCB ? Solder six wires. ? Connect the FPC to the connector.
Blue wire: Main condenser Pink wire: Main condenser Red wire: DC/DC PCB Black wire: DC/DC PCB Yellow wire: DC/DC PCB Blue wire: DC/DC PCB FPC

- A  ?

-

INC
VBA14001-R.3694.A
Main PCB unit

? Mount the main PCB unit (#B1001). ? Tighten two screws (#695). ? Solder the two wires of the electronic buzzer unit. ? Connect the main PCB-FPC (#B1001) to the connector of the DC/DC PCB. ? Connect the connection-FPC (#1023) to the connector, and pass it through the groove.

Main PCB unit (#B1001)

Black wire: Electronic buzzer unit Black wire: Electronic buzzer unit

Connection-FPC (#1023)

Connection-FPC (#1023) #695×2 Groove Connection-FPC (#1023)
Be careful of the direction of the convex portion.

Main PCB unit FPC (#B1001)

- A  ?

-

INC
3. Mounting of Front body on Rear body
Mount the front body on the rear body

VBA14001-R.3694.A

? Mount the front body on the rear body. ? Tighten the screw (#621) and two screws (#615) in the order from ① to ③ . ? Tighten four screws (#634) in the order from ① to ④ . ? Tighten two screws (#699) in the order from ① to ② . ? Attach the eyepiece mold (#291) and fix it with two screws (#615).

#291 #615×2 #634×4




④ ③

#699×2
① ②

#621




② #615×2

- A  ?

-

INC
VBA14001-R.3694.A Inspection and Adjustment of Body back
* "0" positioning of the dial gauge

70 80

60 50 40 30 20

0
10

Surface plate

① Put the tool (J18001-1) on the surface plate, and set the dial gauge to "0". ② Turn the index ring in the direction of the arrow, and set to the scale "17" from "0" that was set in ① . (This is "0"-position of D80.) ③ Measure the body back based on "0" reference position of the index ring.

? Measure three parts from the bayonet face to the CCD-

PCB attaching face.
  Standard:48.50±0.015mm/ Parallelism: within 0.015mm

?In case it is out of standard, make an adjustment

by loosening screws that attach the front and rear bodies, or by putting the washer(s) on the contact surface between the front body and rear body.

Measuring point

Note: For some bodies, washer(s) are already put on the attaching face of the CCD-bracket. There are two cases as follows. 1. Purpose:To adjust the height of the camera body △ (Revision)There are indications by color marker on the CCD-PCB attaching face or under this attaching face of the camera body side. e.g.) Two blue markings : 0.02mm-thick two washers are put on. There are indications by color marker (washer thickness) on the camera body side of the CCD-PCB attaching face. {Blue =0.02mm (#63A), Red = 0.01mm (#63B), Green = 0.06mm (#63C)} * By adding the measured value to the thickness of washers, check if it is within the standard (48.50±0.015mm). 2. Purpose:To adjust the height of the CCD bracket
△ (Revision) on

   There are indications by red marker of the CCD-bracket attaching face. {Red circle = 0.1 mm (#63B)} (Washers are equally put on the three locations.) * When the CCD PCB is replaced, remove the washers. - A 26 ? Changed page △× 2

サービス

計画課

-

Nov.27.2006

10

90

0" position of D80

20



INC
VBA14001-R.3694.A ? Solder four wires. ? Connect the two FPCs to the connector. ? Mount the AF-assist illuminator unit (#B325). ? Mount the sub-PCB unit (#1002) by connecting to the main PCB-connector. AF-assist illuminator #B325
Main PCB connector Sub-PCB unit (#1002)

Black wire: Front body FPC unit Red wire: Front body FPC unit Blue wire: SQ unit Orange wire: SQ unit

Possible to solder other way round

Sub-PCB unit ? Tighten one screw (#623) and two screws (#640). ? Solder three wires. ? Connect three FPCs to each connector.

#623 Black wire: AF-assist illuminator Gray: FG/ID contacts spring #640

Black wire: AF-assist illuminator

#0

Sub-PCB unit (#1002)

- A  ?

-

INC
Assembly of Top cover Outer LCD window / shoe mold unit / accessory shoe / other small parts
Grease: LEN317A

VBA14001-R.3694.A

Apply to all circumferences of clicking area #318 #316

Back side of [#142] #142

Oil barrier: OS-30MF

#B317 #451
Grease: LEN317A

Grease: MZ-800S

#453 #452 #605×3 #326 #640

#463

Adhesive: Super X

#758×2 #756×2

#321

#322 #654×4 #337×2 #336×2 Do NOT leave any gap between [#336] and [#337] when attached. Do NOT let the sponge run off the inside edge of the window.

- A  ?

-

INC
VBA14001-R.3694.A Release button / other small parts

#335

#460 #454

AU TO

#461 #338

#383

#384

#350 #351 #345 #722 #346

#387×2 #347 #349 #340

#398

#399

#348

#339 #380

#690×2

- A  ?

-

INC
VBA14001-R.3694.A Top cover FPC unit

#B11007

#331 #332×2 #1044 #333 #334 #1077

#806 #1017 #1135 #1136 #611 #738 #612 #805 #771

#840 #330 #B1011

#610×4

? Attach the AE-L rubber SW (#399) and AE-L button (#381). ? Mount the top cover FPC unit (#B11007). ? Tighten the screw (#611). ? Tighten the screw (#612). ? Tighten four screws (#610). ? Attach the light-leak prevention sponge (#825).
#610×4

#825

#B11007 #612 #611

#381 #399

AU TO

#825

- A 0 ?

-

INC
VBA14001-R.3694.A AF-assist illuminator window / Command dial ? Attach the command dials (#B367 and #B377). ? Tighten the two screws (#607) of [#B377]. ?Position [#B367] in the direction of the arrow, and tighten two screws (#610). ? Solder the command dials (#B367 and #B377).
#B367
Oil barrier: OS-30MF

#607×2

#B377 Solder

#B367

Direction for positioning

#B367 Solder

#B377

#610×2

M/DFPC unit ? Attach the delete-button rubber SW (#399) and the delete button (#398). ? Mount the M/DFPC unit (#B2455). ? Tighten three screws (#640).

AU TO

#B2455

#398 #399

#B2455

#640×3 #0

- A  ?

-

INC
VBA14001-R.3694.A SB lower case unit ? Attach [#B341] and [#B342]. ? Mount the SB lower case unit (#B2302) on the top cover. ? Insert the SB-case rotate shaft (#306) in the top cover. ? Insert the collar (#308) in the top cover, and fix it by hooking at two places. ? Pass each wire through the hole (#308).
Grease: MZ-800S

#B2302

Grease: MZ-800S

#B341 #B342

Arrangement of built-in SB wires Be careful so that the wires do NOT touch the SB POP UP SW.

AU TO

2 hooks

#306

Dipping
Grease: MZ-800S

Flash-up spring ? Put the flash-up spring (#305). ? Fix it with the screw (#650).

#308

? Hook the flash-up spring (#305) by following the direction of the arrow.
#305

#650

- A  ?

-

INC
VBA14001-R.3694.A Wiring / Top cover FPC ? Arrange the bundled wires. ? Mount the remote control unit (#B1056). ? Tighten the screw (#607).

Bundled wires

#607 #B1056

? Solder the accessory shoe contacts at five places. ? Solder the two SB pop-up SW wires. ? M/D FPC to the connector.

M/D FPC

Yellow: SB pop-up SW wire

Green: SB pop-up SW wire Accessory shoe contacts×5

- A  ?

-

INC
VBA14001-R.3694.A SB upper case

SB flash unit Caution: Both ends of the SB flash unit are just inserted in each part without any adhesive.

Caution: Be careful NOT to deform the SB POP-UP switch.

? Mount the SB upper case (#301) on the SB lower case unit. ? Press the pop-up lever A part of the top cover unit, in order to pop the built-in SB up. ? Tighten two screws (#629).

SB upper case (#301) Claw #629×2 Pop-up lever A part

SB lower case unit

- A  ?

-

INC
VBA14001-R.3694.A Top cover ? Connect the top cover-FPC (#1007) to the connector, and set the top cover. * When AE-CCD positioning adjustment is made, assemble temporarily up to Page A38 without attaching the screws to the top cover, putting the diopter adjustment unit, and soldering six wires.

#1007

? Tighten the screws (#656, #629, and #624) and two screws (#686). ? Put the diopter adjustment unit (#281, #287, #282, #288, and #280).

#280 #288

#282

#281

#287 #686×2

#629

Diopter adjustment unit

#656

#

* After setting the top cover, slide the diopter adjustment lever, and check the movement of the diopter-correcting lens.

- A  ?

-

INC
VBA14001-R.3694.A ? Solder six wires that are connected from the top cover.

Black wire Green wire Orange wire Gray wire

Blue wire Red wire

Preview SW/Fmin GND wire

? Put the preview SW (#227) and preview SW unit (#B228), and fix them with the screw (#627). ? Solder four wires. ? Attach two stickers (#826 and #762).
#826 #762

#627 Preview SW section #627 #B228 #227

Yellow wire Green wire Blue wire

Black:FminSW

- A  ?

-

INC
VBA14001-R.3694.A Preview SW adjustment ① Press the lever (#221) with a screwdriver, etc, from the bottom of the body all the way to the end. ② In the state of ① , adjust by turning the screw (#652) so that [#227] and "A" part slightly touch with each other. ③ Adhere the screw (#652) with the screwlock.
#652 Contact zone

Apply Screwlock

#227

Caution: Perform the work that follows with care, because the preview SW segment can be easily bent.
Press this portion of [#221] all the way to the end.



CCD/PCB unit

? Mount the CCD/PCB unit (#B1032) and tighten three screws (#680). Caution: Some bodies have already washer(s) inserted on the
#B1032

#680×3

CCD/PCB unit mounting surface. (ref. Page A26 for details)

Direction for positioning

- A  ?

-

INC
VBA14001-R.3694.A DG-PCB unit ? Connect the FPC of ※ and two harnesses to each connector. ? Mount the DG-PCB unit (#B1031), and tighten the screw (#683). ? Solder the shield wires at four places. ? Connect two FPCs to each connector.
#683 ※

#B1031

Harness Harness CCD/PCB(core wire: coated) CCD/PCB (ground)

CCD/PCB (core wire: coated) CCD/PCB (ground)

DG shield plate

? Mount the DG shield plate (#B78). ? Tighten six screws (#683).
#683×6

#B78

- A  ?

-

INC
VBA14001-R.3694.A Inspection and adjustment of AE CCD Alignment

WARNING 警告
Take extra care not to get an electric shock when detaching 内部に高電圧部あり。カバーを外す時は感電に注意すること。 covers. カバーを外した後は、修理指針の指示に従ってメインコンデン After removing covers, be sure to discharge the main condenser according to the instructions of repair manuals. サーの放電を必ず行うこと。

* Under the environment where the AE-CCD positioning is adjusted, use the reference body (and change the environment depending on measured results). ? In case the measured value is out of standard, check if there is no misalignment of the grid lines. ? In case the measured value is out of standard, change the environment of measurements. (e.g. setting place/ direction, room brightness, etc) Procedure ① Make temporary assembly of the following four parts: Top cover (connected only with the FPC without tightening the screws), grip cover, I/F cover, and bottom cover (with the tripod base plate being attached.) ② Mount "AF50/1.4D" on the camera, and fix them on the tripod horizontally. ③ Connect the camera and PC via USB cable (UC-E4).       ④ Connect the AC adapter EH-5.   Caution: Be careful NOT to cause a short-circuit at uncovered portions. ⑤ Attach the AE-CCD positioning tool (J15428) in the color viewer (J63070), and turn power ON. ⑥ Keep the 0.7-m distance between the front face of the AE-CCD positioning tool and the reference surface of the camera. Set the camera AF to manual, and the focus ring to "0.7 m" by rotating it. ⑦ Start up the inspection and adjustment software for D80 (J18412), and select "Inspection and Adjustment for AE CCD POSITION" then "Set Camera for AE CCD POSITION". Looking through the viewfinder, move the camera so that the grid lines of the camera coincide with the extension lines of the AE-CCD positioning tool.   * Set the camera and AE-CCD positioning tool horizontally. ⑧ Select "Inspection and Adjustment for AE CCD POSITION".   * Cover the camera with a black cloth, etc, when measured. ⑨ Attach the metering FPC unit with three screws (#514) lightly, then give each screw two turns. By following instructions on PC, make the position adjustment of AE-CCD by the screws (a:#514, b:#514). ⑩ Fix the three screws with screw lock. ? After completing the adjustment,fix the top cover with the screw and inspect the accuracy. If the result is out of standard, make readjustment.
AE-CCD positioning tool (J15428)
Approx. 0.7 m

Attaching surface of the imaging-PCB

AF50/1.4 D

Color viewer (J63070)

- A  ?

-

INC
VBA14001-R.3694.A
Standard → Reference screw X-direction → a: Screw Y-direction → b: Screw X -direction (a) loosening Y-direction (b) loosening

Adhesive: Screwlock

(#B11008) Metering FPC unit

b:#514
X -direction (a) tightening Y-direction (b) tightening

a:#514
Reference screw

Discharge of Main condenser ? Discharge currents from both terminals of the main condenser.

2KΩ/5W

Main condenser

? When the adjustment is completed, remove the temporality attached each cover. Then fix the top cover unit with the screw and solder six wires.

- A 0 ?

-

INC
VBA14001-R.3694.A  Covers ? Mount [#28] and tighten the screw (#638). ? Mount [#B26] and tighten the screw (#618). ? Mount [#B24], and tighten four screws (#691). ? Put the AM change lever (#121), and tighten the screw (#659) and attach [#124].
AU TO

#691×2

#71

#70 #755 #28 #638 #691×2 #124 #659 #121

#B24

#B26

#618

Gap adjustment of SB lighting unit ?In case it is out of standard, pop the SB unit up and make an adjustment by turning the adjusting dial with Hexagonal wrench.

Standard 0 ~ 0.5mm :

Adjusting dial

- A  ?

-

INC
VBA14001-R.3694.A
Assembly of Rear cover

#402 Direction for positioning #403 #412 #413

#424 #425 #426 #427 #428

#421 #422

Grease: LEN317A #416

#401

#670×3

#430 #405×2

#492 #407 #429 #718 #408 #420 #417 #431 #432 #B431 #418 #419 #668 #433 #772×2 #681×2 #B1036 #406 #670×3 #423 #404×2

#1037

Direction for positioning

#666×3

Direction for positioning

- A  ?

-

INC
VBA14001-R.3694.A Rear cover ? Connect TFT-PCB connection FPC to the connector of the DG-PCB.

TFT-PCB connection FPC

? Mount the rear cover, and fix it with two screws (#657) and two screws (#656).

#657×2

#656×2

Rear cover

- A  ?

-

INC
VBA14001-R.3694.A Accuracy inspection and adjustment (Camera body)
★ : New tool

Commercially available straight cable

USB cable: UC-E4

AC adapter: EH-5

Stabilized power supply Set value = 7.4V  0.3Ω 5.0A or AC adapter EH-5

To RS232C terminal

★ Battery tool J61213

J18412 ★ D80 inspection and adjustment software

Use [9pin-25pin] conversion connector for a computer with 9-pin RS-232C terminal. RJ is not available, so use a commercial item.

* Note: When inspecting/adjusting the shutter speed and when adjusting “battery check” voltage, be sure to use the battery tool (J61213). When communications are made by RS232C, supply power from the battery tool. SW-ON sets to communication mode.
Shutter tester (The illustration shows "EF-8000".) J61199 Light receiving adapter (in common with D100)

Flash meter Not prepared as RJ

Measuring adapter (APS) for shutter speed

★ AE-CCD positioning tool (J15428)

Set up in front of color viewer (J63070)

Traditional adapter for camera

AF50/1.4D

AF28/2.8D

When M 1/4000 is adjusted, use the measuring adapter (APS) for shutter speed and the light receiving adapter (J61199). Caution: When the inspection and adjustment are made with the shutter tester, turn the tester ON to light a lamp, and carry out the aging for 3-5 minutes.

- A  ?

-

INC
VBA14001-R.3694.A

D80 Inspection and Adjustment Software (J18412)
This inspection and adjustment software runs on Windows. Install the software by following the below procedure. <Operating environment> Check the following operating environment which is required for installing this program on PC.
PC OS CPU RAM (memory) HD Monitor resolution Interface IBM PC/AT compatible Windows XP Professional Edition, Windows XP Home Edition, Windows2000, Pentium Ⅱ 300MHz ~ Pentium 4 2.2GHz 256 MB or more 6MB-or-more free disk space is required when installing 1024 × 768 pixels or more ※ USB interface (V1.1, 2.0) Serial interface (switchable from COM1 to COM9)

As long as the above hardware requirements are met, any PC such as desktop or laptop, etc is available. < Cautions in starting program > When starting this program, close all the other applications. If some other applications are running, this program may not be activated.

< File > D80.exe     Application execution file NkdPTP.dll    Library file: USB communication application extension file for Windows XP NkdPTPDi.dll  Library file: USB communication application extension file for Windows 2000 PTP      Driver file storing folder for PTP: for Windows 2000

- A  ?

-

INC
VBA14001-R.3694.A <Procedure for installation> The file (PD80.exe) of this program is provided via FD or e-mail. Because this is the self-extracting file, decompress the file before installing, and follow the next procedure.

1. Create a folder for installation under any drive and name.
  (e.g.)C:\D80

2. Paste the file (PD80.exe) in the created folder.

- A  ?

-

INC
VBA14001-R.3694.A 3. Double-click on the pasted file to display the following screen. Press the OK button, then decompression starts.

4. When the decompression of file is finished, the file (D80.exe) is created.

5. The install is completed.

- A  ?

-

INC
VBA14001-R.3694.A Procedure for installing USB driver If this program is used by the USB interface, installing the USB driver is necessary. But if the OS is "Windows XP", the driver is already preloaded so it is not necessary to install it. 1. Set the USB of camera to "PTP".  (SETUP menu → USB setting → PTP) 2. Connect the camera and PC by USB cable.   Turn camera ON. 3. "Add New Hardware Wizard" is indicated, and the next "4." screen is automatically displayed.

4. Click "Yes".

5. Click "Reference". Select "C:\D80\PTPC" of C drive, and click "OK".

6. Reboot the PC to complete the installation.

- A  ?

-

INC
VBA14001-R.3694.A <Start-up of Program> 1. Double-click the file (D80.exe), then Inspection and adjustment program for D80 starts.

2. To display in Japanese, select the radio button "Japanese" in "Language" in the lower right-hand corner of the screen.  However, this is not properly viewed in the English OS.

3. In the pulldown menu of "Communicate", from "COM1" to "COM9" or "USB" is available for "COMPORT". 4. When the "Version" button at the lower-left is pressed, the program version will be displayed. 5. Select each item button according to operation.  Follow the instructions on the next screen that will be shown after pressing the item button. 6. To finish the program, press the "Close (×)" button in the right-hand corner of the screen or "QUIT.".

- A  ?

-

INC
VBA14001-R.3694.A AE inspection and adjustment ① AE CCD alignment inspection and adjustment (ref. Page A39,A40 for details) 《USB connection communication》 ② AE accuracy inspection and adjustment 《USB connection communication》 ③ Aperture accuracy inspection 《USB connection communication》 ④ M1/4000 Accuracy inspection and adjustment 《RS232C connection communication》 ⑤ Adjustment for battery check level (Use the battery tool (J61213) and stabilized power supply.) 《RS232C connection communication》 ⑥ Built-in SB flash inspection and adjustment 《USB connection communication》 〔Tools required〕ref. Page A44. ?AE accuracy inspection and adjustment When AE accuracy inspection and adjustment is made, Two types of lenses (AF50/1.4D and AF28/2.8D) are used. Caution: AE accuracy is not inspected by using the exposure value of the traditional shutter tester. The metering value is displayed on PC screen. ?Battery check voltage level adjustment Connect the battery tool (J61213) to the camera, and turn the communication change-SW to ON. Then make adjustment. ?Built-in SB flash inspection and adjustment Set the distance between camera and flash meter to 1 m, and inspect and adjust the light volume of the built-in SB. (ref. adjustment software for details)

AF inspection and adjustment Note: When using the adjustment software for the first time, prepare three cameras of D80 and measure by "WRITING of AF ADJ. LENS OFFSET VALUE" on the main menu. 《USB connection communication》 ① AF accuracy adjustment (Make the overall following adjustment.) ② YAW, PITCH inspection and adjustment ③ LARK adjustment (inc. CCD output adjustment) ④ AF shift adjustment 〔Tools required〕 1. When adjusting for all adjustment items   ref. Page A44. 2. When inspecting AF accuracy   ① AF adjustment lens (J18266)   ② AF adjusting tool (J15259)   ③ Lens holder for F4 (J15280)   ④ AF chart(J18344)   ⑤ Chart illuminator for AF(J15264) 3. When adjusting YAW, PITCH   YAW, PITCH tool(J18230) 4. When adjusting LARK   The above tool when inspecting AF accuracy In "AF shift adjustment", the distance from the bayonet reference plane to the imaging area (CCD) is calculated by the actual shot photo, and its error is recorded in EEPROM as compensation amount, and adjusted.

- A 0 ?

-

INC
VBA14001-R.3694.A Bottom cover ? Mount the bottom cover and fix it with two screws (#692), the screw (#658), and four screws (#657).

#692×2

#658

#657×4

Bottom cover

∞ Infinity focus inspection & adjustment ?Replace the finder screen with the infinity focus check screen (J18394), and use the reference lens (J18010) and read the value. In case it is out of standard, increase or decrease washers (#836A, #836B, or #836C) for adjustments. * Supply the power (Battery or EH-5) for checking. Caution: When (J18394) is put in to replace the finder screen, put it with the silver spacers upward, which are attached on both sides.
 "0" position

 J18010

Standard: ±0.04mm (1 scale=0.01mm)

#836A #836B #836C

1K602-832 1K602-833 1K602-976

Screen washer A 0.10mm Screen washer B 0.20mm Screen washer C 0.05mm

Reference line

- A  ?

-

INC
VBA14001-R.3694.A

Necessary adjustments when parts are replaced
1. D80 adjustment software and updates
    Adjustments Replacement parts
EEPROM fixed values AE AE CCD accuracy M1/4000 Aperture positioning inspection & inspection & accuracy adjustment adjustment adjustment inspection Built-in SB AF Battery light volume accuracy check volt- inspection & inspection & age level adjustment adjustment adjustment

Shutter unit


* *

Main FPC

















Sub-PCB

AF sensor unit



Top cover or SB lower case unit



DC/DC PCB unit





Metering FPC unit





Aperture control PCB unit



* 1. When the main PCB unit is replaced, be sure to update the version before writing the fixed values. * 2. Make an inspection.

- A  ?

-

INC
VBA14001-R.3694.A

2. Shooting image adjustment software and Software updates
△ Deletion   Adjustments Writing of fixed values writing Replacement parts Image shutter adjust -ment
Pixel defect compensation Black point Pixel defect compensation White point

Gr/Gb difference compensation ADJ (G filter)

Sensitivity

Shading

Gr/Gb com- Sensitivpensation ity ratio adj. (R/B filter)

TFT adjust Factory -ment default setting

Shutter unit

○ ○

Main PCB unit

AF sensor unit

DC/DC PCB unit

Metering FPC unit

*1 DG PCB unit



○ ○

○ ○

○ ○

○ ○

○ ○

○ ○ ○ ○ ○ ○ ○ ○



CCD/FPC PCB unit  TFT monitor

*1.When the DG-PCB unit is replaced, be sure to update the firmware before writing the fixed value.

△ Revision “DG PCB ADJUSTMENT”

サービス

計画課


Changed page △× 2 Oct.23.2006

- A 53 ?

-

INC
VBA14001-R.3694.A Shooting Image Adjustment 1. Summary When D80 shooting image-related and listed parts on Page A53 are replaced, be sure to make an adjustment by the shooting image adjustment software for D80 (J65091). The details of its function and how to use this software are as follows: 2. Adjustment software function  (1) Gr/Gb difference compensation adjustment (G filter)  (2) "Sensitivity" adjustment  (3) Shading adjustment  (4) Gr/Gb compensation adjustment (R/B filter) / Line crawl adjustment  (5) "Sensitivity ratio" adjustment (6) Image shutter inspection and adjustment  (7) Pixel defect compensation - black point  (8) Pixel defect compensation - white point  (9) Getting reference values (10) Factory default setting (11) Checking of the adjustment value (12) Reading of RISC version (13) TFT adjustment ※ When the adjustments from (1) to (5) are made, get in advance the reference values of (9) by using the reference body, then perform the adjustments. 3. Hardware requirements  OS: Windows2000, WindowsXP        Japanese or English OS PC: CPU Pentium Ⅱ or more       Memory 256MB or more       USB1.1 or 2.0  Screen size: 1024×768 pixels or more 4. How to set up Create any directory in the harddisc (except desk top) of PC, and copy the following files.  ?D80IMG.exe?????????Application file  ?D80STD.DAT ???????? Standard file  ?NkdPTP.dll?????????USB-communication application extension file for WinXP  ?NkdPTPDi.dll????????USB-communication application extension file for Win98SE and Win2000  ?CCDFLG.DAT?????????Fixed value data (writing of fixed values)  ?CCDINIT.DAT ????????Initial value data (factory default setting)  ?TFTFLG.DAT ????????Fixed value data  ?TFTINIT.DAT ????????Initial value data (factory default setting)  ?ShadingFittingQ340DLL.dll ?For line crawl, shading  ?ShadingFittingQ340_GLC.ini?System initialization file for line crawl  ?ShadingFittingQ340_SD.ini? System initialization file for shading
 ※ Be sure to copy the above file in the same directory.

- A  ?

-

INC
VBA14001-R.3694.A

6. Basic usage
 (1) Execute "D80IMG.exe" to start up the main screen. (ref. Fig.1)  (2) Select English/ Japanese in Language to display any menu. (ref. Fig.2)  (3) Click the button to start adjustments. ※ When the adjustments from 1. to 5. are made, calculate to get the "Sensitivity" and "Sensitivity ratio" reference values by using the reference body beforehand, then perform the adjustments.  (4) Follow the instructions on screen.  (5) To complete the procedure, click "QUIT" button or "×" button at the upper-right corner of the menu.

Fig.1

Fig.2

- A  ?

-

INC
VBA14001-R.3694.A

7. Required equipment and conditions

※ AC adapter EH-5 and USB cable (mini B type) UC-E4 are used for all adjustments so they are not specified in the list. ★ New tool Item Required device
Luminance LV13 equivalent

1 Gr/Gb difference compensation ?5100K color viewer   J63070
adjustment (G filter)

Setting/Remarks

2 Sensitivity adjustment

(ex-model viewer J63049 is also available.) ?Luminance meter BM-3000 J63068 ?Tool lens (to fix aperture)  J61185 ?SP2 (G filter) J63086 ?5100K color viewer   J63070 (ex-model viewer J63049 is also available.) ?Luminance meter BM-3000 J63068 ?Tool lens (to fix aperture)   J61185 ?ND filter  (ND8×1+ND4×1)

Aperture F5.6 Luminance LV13 equivalent

3 Shading adjustment

?5100K color viewer   J63070 (ex-model viewer J63049 is also available.) ?Luminance meter BM-3000 J63068 Aperture F5.6 ?Tool lens (to fix aperture)  J61185 Use the packaged product; 3-step light ?ND filter (ND8×1) reduction Gr/Gb compensation adjustment ?5100K color viewer   J63070 Luminance LV13 equivalent 4 (R/B filter) (ex-model viewer J63049 is also available.) / Line crawl adjustment ?Luminance meter BM-3000 J63068 Aperture F5.6 ?Tool lens (Fixed aperture) J61185 ?SP3 (R filter)  J63087 ?SP1 (B filter)  J63085 Luminance LV9 ? Shutter tester 5 Sensitivity ratio adjustment ?Luminance meter BM-3000 J63068 Aperture F5.6; No filter ?Tool lens (to fix aperture)  J61185 Inspection luminance LV13 equivalent ?5100K color viewer   J63070 (ex-model viewer J63049 is also available.)

Aperture F8 52 mm, Use the packaged product; 5-step light reduction Luminance LV13 equivalent

6 Image shutter inspection and
adjustment

? Shutter tester ?Luminance meter BM-3000 J63068 ?Tool lens (to fix aperture)  J61185 ?5100K color viewer   J63070 (ex-model viewer J63049 is also available.) ?Luminance meter BM-3000 J63068 ?Tool lens (to fix aperture)  J61185

Luminance LV9, 15 Aperture F5.6 Luminance LV13 equivalent

7 Pixel defect compensation black point

Aperture F5.6

8 Pixel defect compensation 9 Getting of reference values 10 Factory default setting 11 Checking of adjustment value 12 Reading of RISC version
13 TFT adjustment white point

Body cap or lens cap

Environmental temperature approx. 20 - 25℃ Same as "Sensitivity adjustment" and "sen- No filter when sensitivity ratio reference value is calculated. sitivity ratio adjustment". None None None None

- A  ?

-

INC
VBA14001-R.3694.A 8. Summary  The summary on each adjustment is as follows:  (1) Gr/Gb difference compensation adjustment (G filter) Camera is faced to the light-emitting box (color viewer) of LV13 equiv. with SP2 (G filter) being put between them. G-line crawl (3895×2610 pixels) is divided into (29×25) blocks, and the adjustment is made so that the difference between Gr and Gb output can fall in the standard range.

 (2) Sensitivity adjustment Camera is faced to the color viewer of LV13 equiv. with ND filter (-5 steps) being put between them, and the adjustment is made by changing the ampgain so that G output can fall in the standard range. The gain value is adjusted so that the G output average value (Average of Gr/Gb) in the center (425×425 pixels) can reach the target output level (approx. 1040LSB). The actual adjustment of the gain value is made only under the condition of ISO100 and ISO1600, and the medium sensitivity is calculated by the adjustment values of these 2 conditions. For target output level, G output average of sensitivity reference value (ISO100) is used, which was calculated by the reference body.  (3) Shading adjustment (5100K color viewer is shot by this camera, and adjustment is made.) Camera is faced to the color viewer of LV13 equiv. with ND filter (-3 steps) being put between them, and the adjustment of white balance distribution is made for 3 areas [Area ① : Central 1936×1926-pixel area; Area ② : All the divided areas except ③ -areas after dividing (3890×2606-pixels) into (29×25-pixels); Area ③ ; 4 corners of (4×6-pixels) after dividing (3890×2606-pixel) into (29×25-pixels)]
Area ③ 4x6  Area ① 1936x1926 Area ③ 4x6 Area ② 29x25 Area ③ 4x6 Area ③ 4x6

Caution:If "Data read error" is occurred by PC environment, remove the AC adapter EH-5 and insert it, reboot adjustment software, change the delay time, then execute from "Shading" again.

  (4) Gr/Gb compensation adjustment (R/B filter) / Line crawl adjustment Camera is faced to the light-emitting box (color viewer) of LV13 equiv. with SP3 (R filter) or SP1 (B filter) being put between them, and the adjustment is made so that the difference in G output average between B-G line and G-R line, when the whole screen is divided in areas, can fall in the standard range.  (5) Sensitivity ratio adjustment With the shutter tester of LV9, the adjustment is made so that the R/G, B/G output becomes the same as the output ratio of the sensitivity ratio reference value that was calculated by the reference body. The adjustment is made only under the condition of ISO100, and the average value of the center (425 pixels × 425 pixels) is used. After the adjustment, check with the 5100K color viewer.   (6) Image shutter adjustment Based on the 1/60 sec. data of LV9, fine-tune the 1/4000 sec. data of LV15. After the adjustment, release the shutter and inspect data deviation nine points of the shot image.

- A  ?

-

INC
VBA14001-R.3694.A  (7) Pixel defect compensation - black point When pixels of which the output level is under specified value with LV13 equiv., are detected, the coordinates of the detected pixels are rewritten as pixel defect compensation data.  (8) Pixel defect compensation - white point Shots are taken on the dark surface. In case the pixel output is found to be beyond the standard value, the detected pixel coordinate is additionally written as the pixel defect compensation data.  (9) Getting of reference values   ?Sensitivity reference value calculation The reference body is faced to the color viewer of LV13 equiv. with the ND filter (-5 step) being put between them. Then, store the G output average value of the center (425 pixels × 425 pixels) is stored in the D80BSD.DAT file as the sensitivity reference value.   ?Sensitivity ratio reference value calculation The reference body is faced to the shutter tester of LV 9 equiv. (without filter) and LV13 equiv. (without filter). Then, the sensitivity ratio reference value GR and GB is calculated, based on the G/R/B output average of the center (425 pixels × 425 pixels), and they are stored in the D80BSD.DAT file. It is necessary to calculate the reference values of "Sensitivity" and "Sensitivity ratio" in order to prevent the color temperature fluctuation caused by color viewer's changes over time from affecting the results of the shooting image adjustment. By using the reference body, calculate the reference values once in about every 3 months, when the fluorescent of the color viewer is replaced.  (10) Factory default setting   By reset the settings of camera, factory default settings are restored. Select the language and video mode to perform. Because this setting of RP DG-PCB is blank, be sure to set the initial default setting when the DG-PCB is replaced. When this setting is used, the USB mode is set to "Mass Storage" mode.  (11) Checking of adjustment value The adjustment value is confirmed, functioning as substitute for the traditional "READING AND REWRITING OF EEPROM DATA.".  (12) Reading of RISC version The RISC firmware version is displayed.  (13) TFT adjustment Flickering, color and luminance of TFT are adjusted. ※ Whenever the DG-PCB and TFT monitor are replaced, be sure to perform "REWRITING THE TFT FIXED VALUE.".

- A  ?

-

INC
VBA14001-R.3694.A 9. Procedure 9-1. Shooting image adjustment ● Calculate the "Sensitivity" and "Sensitivity ratio" reference values by using D80 reference body beforehand, then perform the adjustments. (ref. 9-4.)  ● For shooting image adjustment, make all items from (1) to (6). The adjustments from (1) through (6) are all programmed to be executed in serial order. When 1 item is completed, the software automatically goes on to the next adjustment.  ● In case adjustments are interrupted by NG, the adjustments can be continued again after NG. As for adjustments that were ended with OK, the flash memory updates of the adjustment value are completed. Note: Adjustments are not possible without resetting "Custom setting" of this camera.      Before the adjustments, record the details of "Custom setting" set by customers if necessary. Start adjustments  ?Provide the power for the camera via AC adapter.  ?Reset "Custom setting".  ?Set "PTP" mode by Setup menu.  ?Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera.  ?Connect the camera and PC via USB cable.  ?Set the luminance of the color viewer to LV13 equivalent.  ?Set the shutter tester to LV9. (1) Gr/Gb difference compensation adjustment (G filter)  ?Click "1. Gr/Gb COMPENSATION ADJ (G FILTER)" of the main menu on screen.  ?Attach the tool lens (Aperture F5.6) and SP2 (G filter) to the camera.  ?Get the camera closest to the center of the illuminated surface of the color viewer.  ?The adjustment starts. When it is completed, "OK" is displayed.  ?The software automatically goes on to the next adjustment item.  (2) Sensitivity adjustment  ?Click "2. SENSITIVITY ADJUSTMENT" of the main menu on screen.  ?Attach the tool lens (Aperture F8) and ND filter (ND 8× 1+ ND 4 ×1)to the camera.  ?Get the camera closest to the center of the illuminated surface of the color viewer.  ?The adjustment starts. When it is completed, "OK" is displayed.  ?The software automatically goes on to the next adjustment item.  (3) Shading adjustment  ?Click "3. SHADING ADJUSTMENT" on the menu. ?Attach the tool lens (Aperture F5.6) and ND filter (ND 8× 1) to the camera.  ?Get the camera closest to the center of the illuminated surface of the color viewer.  ?The adjustment starts. When it is completed, "OK" is displayed.  ?The software automatically goes on to the next adjustment.  ?The software automatically goes on to the next adjustment item.
Caution: If "Data read error" is occurred by PC environment, remove the AC adapter EH-5 and insert it, reboot adjustment software, change the delay time, then execute from "Shading" again.

- A  ?

-

INC
VBA14001-R.3694.A  (4) Gr/Gb compensation adjustment (R/B filter)  ?Click "4. Gr/Gb COMPENSATION ADJ (R/B FILTER)" on the menu.  ?Attach the tool lens (Aperture F5.6) and SP3 (R filter) to the camera.  ?Get the camera closest to the center of the illuminated surface of the color viewer.  ?The adjustment starts. When it is completed, the next instructions are displayed.  ?Attach the tool lens (Aperture F5.6) and SP1 (B filter) to the camera.  ?Get the camera closest to the center of the illuminated surface of the color viewer.  ?The adjustment starts. When it is completed, "OK" is displayed.  ?The software automatically goes on to the next adjustment.  (5) Sensitivity ratio adjustment  ?Click "5. SENSITIVITY RATIO ADJUSTMENT" of the main menu on screen.  ?Attach the tool lens (Aperture F5.6) to the camera (without filter).  ?Get the camera closest to the center of the illuminated surface of the shutter tester.  ?The adjustment starts. When it is completed, "OK" is displayed.  ? Get the camera closest to the center of the illuminated surface of the color viewer.  ?The adjustment starts. When it is completed, "OK" is displayed.  (6) Image shutter adjustment  ?Click "6. IMAGE SHUTTER INS. & ADJ." of the main menu on screen.  ?Attach the tool lens (Aperture F5.6) to the camera (without filter).  ?Get the camera closest to the center of the illuminated surface of the shutter tester.  ? Make inspection and adjustment with the luminance LV9 and LV15.  ? Confirm that the inspection is within standard. 9-2. Pixel defect compensation - black point  ?Set the color viewer luminance to LV13 equiv.  ?Provide the power for the camera via AC adapter.  ?Reset "Custom setting".  ?Set "PTP" mode by Setup menu.  ?Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera.  ?Connect the camera and PC via USB cable.  ?Click "BLACK POINT" of "PIXEL DEFECT COMPENSATION" of the menu.  ?Attach the tool lens (Aperture F5.6) to the camera (without filter).  ?Get the camera closest to the center of the illuminated surface of the color viewer.  ?When the adjustment starts, pixel defects are detected, displaying the number of pixels and addresses.  ?After confirming the above, click "X" button.  ?When it is completed, "OK" is displayed.  ?The software automatically goes on to the next "WHITE POINT" of "PIXEL DEFECT COMPENSATION". (After the black point compensation, be sure to perform the white point compensation, too.) Note: In some cases, NG occurs due to dusts on the CCD.     Be sure to clean the CCD surface before adjustments.

- A 0 ?

-

INC
9-3. Pixel defect compensation - white point  ?Check the environmental temperature (approx. 20-25°C.).  ?Provide the power for the camera via AC adapter.  ?Reset "Custom setting".  ?Set "PTP" mode by Setup menu.  ?Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera.  ?Connect the camera and PC via USB cable.  ?Click "WHITE POINT" of "PIXEL DEFECT COMPENSATION" of the menu.  ?Cap the camera with the body cap or lens cap to shield light from the mount.  ?When the adjustment starts, pixel defects are detected, displaying the number of pixels and addresses.  ?After confirming the above, click "×" button.  ?When it is completed, "OK" is displayed. 9-4. Getting of reference values  ?Set the color viewer luminance to LV13 equiv.  ?Provide the power for the camera via AC adapter.  ?Reset "Custom setting".  ?Set "PTP" mode by Setup menu.  ?Set the focus mode to M, exposure mode to M, and the exposure compensation to "0" of the camera.  ?Connect the camera and PC via USB cable.  ?Select "OBTAIN REFERENCE VALUE." of the menu on screen.  ?Click "Start".  ?The calculation of the sensitivity reference value starts. The message to set conditions is displayed.  ?Attach the tool lens (Aperture F8) and ND filter (ND 8× 1 + ND 4 ×1) to the camera.  ?Get the camera closest to the center of the illuminated surface of the color viewer.  ?The obtaining starts. When it is completed, the software goes on to the sensitivity ratio reference value.  ?Attach the tool lens (Aperture F5.6). (Remove ND filter).  ?Get the camera closest to the center of the illuminated surface of the shutter tester of LV9.  ?Get the camera closest to the center of the illuminated surface of the color viewer of LV13 equiv. ?The confirmation of acquired value starts. When it is completed, the sensitivity and sensitivity reference values are stored in the standard setting file (D80BSD.DAT). ?After this procedure, when the shooting image adjustment is made, the sensitivity and sensitivity ratio that were calculated this time are used. ※ Calculate the sensitivity and sensitivity ratio reference values once in about every 3 months, and when the fluorescent of the color viewer is replaced. 9-5. Reading of RISC version  ?Provide the power for the camera via AC adapter.  ?Set "PTP" mode by Setup menu.  ?Connect the camera and PC via USB cable.  ?Click "RISC VERSION" of the menu on screen.  ?RISC version is displayed. VBA14001-R.3694.A

- A  ?

-

INC
9-6. Procedure for upgrading RISC firmware: VBA14001-R.3694.A  ? After preparing the CF card, copy the latest version ( XXXX. BIN) into the root directory.  ? Insert the CF card, and select "FIRMWARE VERSION" from the SETUP menu.  ? Follow the instructions on screen for version upgrading. It takes approx. 3-4 minutes.  ? Check the version of firmware by "RISC VERSION" of the image adjustment software.  Note: In case incorrect files are included in the CF card, the details for updating are not displayed even after selecting "FIRMWARE VERSION" from the SETUP menu.

9-7. TFT adjustment  ?Provide the power for the camera via AC adapter.  ?Connect the camera and PC via USB cable.  ?Turn the camera ON.   Flicker adjustment  ?Usually the default value can be used, and this adjustment is not necessary.  ?If flicker can be checked with eyes, drag the slider and adjust the camera’s monitor not to flicker.  ?Remove the USB cable from the camera, and also remove the AC adapter without turning the power OFF.     Hue adjustment  ?Usually the default value can be used, and this adjustment is not necessary.  ?If improper hue can be checked with eyes, drag the slider and adjust the camera’s monitor not to flicker.  ?Remove the USB cable from the camera, and also remove the AC adapter without turning the power OFF.   Luminance adjustment  ?Usually the default value can be used, and this adjustment is not necessary.  ?If improper hue can be checked with eyes, drag the slider and adjust the camera’s monitor not to flicker.  ?Remove the USB cable from the camera, and also remove the AC adapter without turning the power OFF.

- A  ?

-

INC
VBA14001-R.3694.A

< Measurement of Consumption current value >
When this camera is used for measuring the consumption current value, connect the battery tool (J61213), and turn the change-SW to OFF. Then make measurements based on the following.

7.8V 0.3Ω - +

+ A



Turn change-SW to OFF.

《Inspection standards》
Main SW?OFF

Test item

200 μ A or less

Standard

Test condition
ref. above. AF50/1.4D、EV12

All operational buttons are NOT pushed. Main SW?ON (Half-release timer OFF) Main SW?ON (Half-release timer ON) Main SW?ON (Illumination ON) Main SW?ON (TFT ON)

200 μ A or less 200 μ A or less 300 μ A or less    1 A or less

Caution: When the consumption current value is measured, backup battery must be fully charged.

- A  ?

-

INC
VBA14001-R.3694.A Cleaning between Penta prism and SI-LCD 《In case of cleaning by NOT removing the screen box》  ?Take out the two screws (#689), and remove the mirror receiving part.

#689×2

 ?Release the claw (indicated by the arrow) of the screen box retaining plate (#511), and lower [#511].

Screen box

#511

 ?Pull the screen box section down straightforward until the position shown in the picture. * Do NOT pull down with force because the FPC is connected.  ?Cleaning by blower is possible from the arrowindicated area.  ?After the cleaning, reassemble the screen box by pushing right upward, and fix with the screen box retaining plate (#511).

《In case of cleaning by removing the screen box》  ? Remove the front cover. Disconnect the SI-FPC from the connector, then it is possible to remove the screen box section, and carry out cleaning.
SI-FPC

Screen box section

Caution: When the above cleaning is carried out, check the positioning of the finder field frame 1 (#263), then make assembly. After the assembly, inspect the focusing of the viewfinder. (Refer to Page A15 for positioning.)

- A  ?

-

INC
VBA14001-R.3694.A
メインコマンドダイヤル M C/D UNIT

実体配線図 WIRING
リモコン受光素子
Remote IC Connected with this connector Connected with this connector M/D FPC部組 Mode dial FPC

サブコマンドダイヤル S C/D UNIT
コネクタ接続 コネクタ接続

BATTERY CONTACT SPRING 電池接点 + FG -

Connected with this connector

コネクタ接続
RED 赤 GREY 灰 BLACK 黒

Connected with

ポップアップMg
ゼブラ圧接接続

コネクタ接続 this connector
Connected with this connector

コネクタ接続

Zebra pressure welding

Zebra pressure welding (Back side)

ゼブラ圧接接続 (裏側)
YELLOW 黄 BLACK 黒

POP UP Mg

Connected with コネクタ接続 this connector

Connected B to B this connector B to B接続 (Back side) (裏側)

コネクタ接続 this connector コネクタ接続 this connector 半田ブリッジ接続
Connected with

Connected with

外部LCD Out side LCD

緑 GREEN

黄 YELLOW

ポップアップSW AF補助光
AF assist illuminator POP UP SW

Soldering bridge
コネクタ接続 Connected with this connector コネクタ接続 Connected with this connector

Connected B to B this connector

B to B接続

コネクタ接続 this connector コネクタ接続(裏側)this connector(Back side)
Connected with

Connected with

ゼブラ圧接接続

D/GメインFPC

圧電ブザー
BUZZER UNIT
△訂正 Revision ORANGE 青 橙 BLUE BLUE 青 ORANGE 橙

Zeabra pressure welding

D/G-Main FPC
Connected with this connector コネクタ接続 コネクタ接続 (裏側) Connected with this connector (Back side)
7 6 5 4 3 2

コネクタ接続 Connected with this connector

Connected with this connector

コネクタ接続 (上接点)

SQモータ SQ motor unit

コネクタ接続 Connected with this connector

コネクタ接続 Connected with this connector
10 9 8 7 6 5 4 3 2 8

半田ブリッジ接続

Soldering bridge

コネクタ接続 (裏側) Connected with this connector (Back side)

バックアップ電池 Buckup battery

シャッターユニット
Shutter unit

VIORET WHITE GREY GREEN ORANGE

紫 白 灰 緑 橙

茶 BROWN

黒 BLACK

Soldering bridge
半田ブリッジ接続 コネクタ接続 (上接点) Connected with this connector(up Contact)

BLACK 黒

RED 赤

撮像素子 Picture Element
コネクタ接続 Connected with this connector コネクタ接続 Connected with this connector

Fmin SW Fmin スイッチ
半田ブリッジ接続

黒 BLACK 黄

Soldering bridge

コネクタ接続 Connected with this connector

Aperture Mg

コネクタ接続 Connected with this connector

絞りMg

緑 GREEN RED 赤 緑 GREEN

赤 RED 青 BLUE 灰 GREY 橙 ORANGE 緑 GREEN

AFモータ AF motor

SB発光部
Built-in Flash

Connected with this connector

プレビューSW1
Preview SW1
黄 YELLOW 橙 ORANGE 黄 YELLOW

AP-PI



YELLOW


プレビューSW2
Preview SW2
BLUE 青

BLACK

TFTモニタ
TFT MONITER

コネクタ接続

絞りPI

黒 BLACK

シーケンスモニタSW
Sequence Monitor SW
GREEN 緑

レンズ着脱/AFMF切替SW Lens release/AF/MFSW

DCDC基板
DC-DC PCB
SBSB+ DCDC+ コネクタ接続
BLUE 青 YELLOW 黄 BLACK 黒 RED 赤

青 BLUE 桃 PINK

シーケンスSW
Sequence SW

AFPI BATBAT+





コネクタ接続 (裏側)

BLACK

RED

Connected with this connector

Main condenser

メインコンデンサ

サービス

Connected with this connector(Back side)

計画課

差し替えページ △×1 Changed page △× 1


- E1 Dec.25.2006

INC
Inspection standards
Items External view Step (height difference) Judgment standard Between top cover and apron: 0.2 mm or less Other parts: 0.3 mm or less Moving parts: 0.5 mm or less
from Top cover to Apron; to I/F cover: 0.2 mm or less from Bottom cover to Apron; to I/F cover: 0.2 mm or less from Top cover to around grip strap eyelet: 0.3 mm or less from Top cover to around rear cover strap eyelet: 0.4 mm or less When SB is housed, from SB upper case to Top cover; to Apron: 0.3 mm

VBA14001-R.3694.A

Remarks Visual check Digital micrometer

Clearance

or less Other parts: 0.3 mm or less Moving parts: 0.5 mm or less Size / Force Shutter release button Protrusion: 0.8 ± 0.2 mm Halfway pressing force: 00 ± 50 g Halfway pressing stroke: 0.6 ± 0.2 mm Releasing force: 260 ± 70 g Releasing stroke: 0.8 ± 0.25 mm   (Half-release pressing ON) Extra stroke after releasing button: 0.6 mm or more Difference btwn Half-releasing and Full pressing force: 5 g or more Digital micrometer Tension gauge

Aperture lever Main mirror

3.4 height: 3.4 + 0. mm 45 ゜ angle: Up-down ± 0'      Right-left ± 30'  Distortion: 8' or less Clearance for up-mirror in mirror box: None 59 ゜ angle: Up-down 0 ± 20' Distortion: 8’ or less

3.4 height gauge Collimator Main mirror tool Visual check Feeling in hand Sub-mirror tool

Sub-mirror

∞ Infinity focus

±100μm

Collimator ∞ focus lens

- R ?    -

INC
VBA14001-R.3694.A Items AF accuracy Yaw Center:± 4 mrad Others: ± 0 mrad Center : ± 5 mrad Others: ±  mrad Others than Side: 0 ± 50μm (Average of 3 times or more) Judgment standard Remarks PC Special tool Brightness box

Pitch

Def amount

AF-assist illuminator Lighting level AE accuracy Exposure on image

Switchable from OFF to ON with EV4.5 - 5.5

Brightness box SB-800 Shutter speed tester AF50/.4D

/4000: ±0.65EV (excl. AMP) Speed at less than /4000 ~ /2000 or more: ±0.65EV Lower speed at less than /2000: ± 0.5EV

Dispersion

Speed at /2000 or more: 0.6EV or less Lower speed at less than /2000: 0.3EV or less Difference in Metering mode: 0.3EV or less * AE-A mode, each metering mode, ∞, ISO100  Note: AMP: EV3 - 0      SPOT : EV2 - 20 Data spread in min. aperture/ continuous shooting: 0.5EV

Shutter accuracy Speed accuracy

Speed at more than /2000: ± 0.55EV /2000: ± 0.35EV (/2000) ~ 30:±0.25EV

Shutter speed tester

Dispersion

/4000 - (/2000): 0.4EV or less /2000 - (/000): 0.3EV or less /000 - 30: 0.25EV or less

Shutter curtain speed

Both front and rear curtains (6.6mm or less): approx. 3.8 ms or less Black/white bound (within screen frame): None Time lag: -0.05-0.5 ms

Shutter curtain bound Synchronization

- R2 ?    -

INC
VBA14001-R.3694.A Items Viewfinder Inner LCD lower panel window position Judgment standard Remarks

Up-down position: 0.5 - 1.25a (a= LCD width) from the finder field frame Tilt: °or less Tilt: (Right-left tilt from the lower part of finder field frame): 30’ or less Relative angle to image sensor: 30’or less

Visual check Shoot the finder field frame with the 0.2-mm-or-less tilt of optical axis from the viewfinder eyepiece optical axis, and measure the angle. AF50/.4D, F5.6 Measure a difference in the center btwn the marked finder field and actual shot object. Eye point tool Vernier caliper

Finder field frame

Field of viewfinder (frame covage) Parallax (Difference of center from the shot image/ sensor) Eye point Battery life EN-EL3e

In height and width: 95 +3 % -2 Up-down: 0.5 mm or less Right-left: 0.5 mm or less

Distance to eyepiece protective glass: 9.5 ± 0% Professional mode  Room temperature: 2500 frames or more   0℃ : : 900 frames or more
?Setting

ISO00, Exposure mode: M, /250 sec., F6, AF-C, operation mode: C, Panasonic RP-SDK52JA, Illuminated surface: LV2, Image quality: BASIC, Image size: M, White balance: A, Halfway press→ Card format → Repeat the below “Operation” → Remove the card when the no. of exposures remaining becomes “0” → Card format →…

?Lens:[AF-S DX8-35/3.5-5.6G] ?Operation: Halfway press for 3 sec. → AF-scan reciprocating motion 3 times → Continuous releases 6 times → TFT playback for 5 sec.→ Half-release timer OFF waiting for 6 sec.

General mode  Room temperature: 500 frames or more 0℃ : 400 frames or more
?Setting ISO00, Exposure mode: M, /250 sec., F6, AF-C, operation mode: S, Panasonic RP-SDK52JA, Illuminated surface: LV2, Image quality: NORM, Image size: L, White balance: A, Halfway press→ Card format → Repeat the below “Operation” → Remove the card when the no. of exposures remaining becomes “0” → Card format →… ?Lens:  AF-S DX ED8-70/3.5-4.5G(IF) ?Operation: Repeat the following the odd-numbered shots and even-numbered shots until the number of exposures remaining becomes "0". Switch power OFF for  min. each time 0 frames are shot. Shots Repeat operation Odd-numbered shots ① Halfway press 5 sec. ② AF scan reciprocating motion once ④ TFT playback 5 sec. ⑤ Half-release timer OFF waiting 6 sec. ※ Activate the flash of AF-assist illuminator. Even-numbered shots ① Halfway press 5 sec. ② AF scan reciprocating motion once ③ Release… Built-in SB full flash ④ TFT playback 5 sec. ⑤ Half-release timer OFF waiting 6 sec. ※ Do NOT activate the flash of AF-assist illuminator.

MENU ① - ⑤ . ③ Release… Built-in SB full flash

- R3 ?    -

INC
VBA14001-R.3694.A Items Standby / consumed current Judgment standard Main SW / OFF: 250μA or less (Do NOT press any operational buttons.) Main SW / ON (Half-release timer: OFF): 250μA or less Main SW / ON (Half-release timer: ON): 250μA or less Main SW / ON (Illumination: ON): 300μA or less Main SW / ON (TFT ON): A or less Operation time / consumption current accumulated Lens scan AF50/.8  Operation time: 000 ms or less      Consumption current accumulated: 500mAsec or less AF70-20/4-5.6 Operation time: 2000ms or less     Consumption current accumulated: 800mAsec or less   Preview   Operation time: 200ms or less     Consumption current accumulated: 20mAsec or less Release without memory card Operation time: 300ms or less     Consumption current accumulated: 250mAsec or less Clock accuracy BC level Difference par month: ±30 seconds (20℃) Level 5: 5 lights up  Charge remaining: 70 ~ 00% Level 4: 4 lights up  Charge remaining: 50 ~ 69% Level 3: 3 lights up  Charge remaining: 35 ~ 49% Level 2: 2 lights up  Charge remaining: 20 ~ 34% Level :  light up  Charge remaining:  ~ 9% Level 0:  light blinking Charge remaining: 0% When special Li-ion is used: 2 and a half hours or more Wave clock Check the level in the LCD control panel on top of camera or TFT battery information Communicationcapable battery tool Clock Remote wire Remarks Constant-voltage power source (5A or more) Battery tool (J623) Ammeter AF50/.4 EV2 Constant voltage power source (5A or more) Battery tool (J620) Special tool Oscilloscope LV2

Bulb battery life

- R4 ?    -

INC
VBA14001-R.3694.A

工 具?TOOLS 
★:新規設定工具?NEW TOOL
工具番号 Tool No. J15428 名 称 Name of tool AE CCD 位置出し工具 AE CCD positioning tool J18394 無限合致調整用スクリーン Infinity focus adjustment screen J18389 反射ミラー Reflection mirror J18412 カメラ部点検、調整ソフト Inspection and adjustment software for CAMERA J65091 撮像部点検、調整ソフト Inspection and adjustment software for IMAGING J18230 YAW、PITCH工具 Yaw,Pitch adjustment tool J15259 AF調整工具台 AF adjusting tool J15280 Zレンズ用支持ホルダー Lens holder J15264 高周波タイプ蛍光灯器具 Illumination box for AF adjustment J18266 AF調整用Zレンズ(1m用)    Z adjustment lens (For 1m) J15274 J15264 用チャートボード Chart board for J15264 J18344 AFチャート AF adjusting chart FOR D100,D70,D70s.D50.D200 FOR F5,F100,D70,D70s.D50. D200 FOR F5,F100,F90,F90X,D70,D 70s.D50.D200
FOR D200 FOR D200

備 考 Others







- T ?

-

INC
VBA14001-R.3694.A

★:新規設定工具?NEW TOOL
工具番号 Tool No. J19110 名 称 Name of tool 小型バック出しコリメータ  Back focus collimator 備 考 Others

J18409

サブミラー59°出し工具 Sub mirror angle adjustment tool


J18037-2

オプチカルパラレル Optical parallel

J18004

絞りレバー高さ点検工具 Aperture lever positioning gauge

J19004-1

インジケータ及びスタンド (ボディバック台、ゲージ) Dial indicator and Stand

J18001-1

ボディバック出し工具 Body back focus gauge

J19001

無限合致コリメーター F=600mm Collimator F=600mm

J18010

無限大合致基準レンズ 50/1.8 Infinity Standeard Lens 50/1.8

払底品

J61199

D100 AE 受光部アダプター D100 LIGHT RECEIVE ADAPTER

FOR D100,D2H,D2X

J19123

シャッタ-試験機 EF- 1(CE) Shutter Tester EF-1(CE)

共立電機製 KYORITSU ELECTRIC
EF -8000 usable

- T ?

-

INC
VBA14001-R.3694.A

★:新規設定工具?NEW TOOL
工具番号 Tool No. J18267 名 称 Name of tool AF50/1. 4D Lens AF50/1.4D 備 考 Others

J61185

撮像関係調整用レンズ D1 Standard lens

FOR D1,D2H,D70,D70s,D50 D200

J18191

NDフィルタ-8X ND filter 8X

FOR D2H,D70,D70s,D50.D200

J18358

NDフィルタ- 4 X ND filter 4X

1 枚使用 It uses by one pieces

J63070

カラービュワー Color Viewer

J63068

輝度計(BM-3000) Luminance Meter BM-3000

J63085

????? SP1 (75X75MM) Filter SP1 (75X75MM)

FOR D2H,D70,D70s,D50.D200

J63086

????? SP2 (75X75MM) Filter SP2 (75X75MM)

FOR D2H.D200

J63087

????? SP3 (75X75MM) Filter SP3 (75X75MM)

FOR D2H,D70,D70s,D50.D200

J61213



電池工具 Battery tool

J19109

MC-31(接続コード) MC-31 (CONNECTING CORD)

- T ?

-

INC
VBA14001-R.3694.A

★:新規設定工具?NEW TOOL
工具番号 Tool No. OS-30MF 名 称 Name of tool ドライサ-フ OS-30MF DRY SURF OS-30MF(OIL BARRIER) 備 考 Others

LEN317A

グリース LEN317A Grease LEN317A ネシ゛ロック(赤)1401C Screw lock 1401C セメダイン 8008(黒) Cemedain 8008(BLACK) ドライサ-フ MZ-800S DRY SURF MZ-800S アロンアルファ Crazy glue フラッシュメーター Flash Meter デジタルマルチメータ Digital meter ACアダプター EH-5 AC adapter EH-5 USBケーブル UC-E4 USB cable UC-E4 パーソナルコンピュータ Personal computer 安定化電源(10 V 5 A ) Power supply(10V 5A) へクスキー(φ 1.5mm) HEX.KEY WRENCH ( φ 1.5mm) AF28/2. 8D Lens AF28/2.8D 汎用品 RJ is Not available 汎用品 RJ is Not available 汎用品 RJ is Not available 製品転用 RJ is Not available 製品転用 RJ is Not available 汎用品 RJ is Not available 汎用品 RJ is Not available 汎用品 RJ is Not available 製品転用 RJ is Not available

EDB0011

C-8008B

MZ-800S

- T ?

-


更多相关文章:

非常超级学习网 fccjxxw.com

copyright ©right 2010-2021。
非常超级学习网内容来自网络,如有侵犯请联系客服。zhit325@126.com|网站地图